★ FMCSA-Registered Provider Listed on the Federal Training Provider Registry
1-814-304-7635
ELDT.Courses
Trucking by State

Washington CDL and Trucking Guide

To get a CDL in Washington, you pass the Department of Licensing (DOL) knowledge tests for a commercial learner's permit, wait 14 days, finish your training, then pass a three-part skills test with a DOL examiner or a state-certified third-party examiner. Washington has its own state training requirements on top of federal entry-level driver training (ELDT), and DOL will not test you until both are on record.

ELDT.Courses does not offer CDL or ELDT training in Washington. ELDT.Courses does not hold a training provider or school license in Washington. This page explains the state rules and how to find training the state accepts.

Last verified:

Get the free Washington CDL cheat sheet → One printable page, with your permit and license costs if you want them.

01CDL Basics

Getting a CDL in Washington

Washington CDL at a glance
Licensing agencyThe Washington State Department of Licensing (DOL) issues commercial learner's permits and CDLs.[1][2]
Official CDL manualWashington Commercial Driver License (CDL) Guide (PDF). DOL has replaced Sections 11 and 12 of the guide with a separate supplemental guide for the vehicle inspection and basic control parts of the skills test. Both are on DOL's commercial driver guides page.[3][4]
Minimum age18, with a valid Washington driver license. You must be 21 to drive a commercial vehicle from state to state.[2][5][6]
Learner's permitThe commercial learner's permit costs $40 and is good for 180 days. You can renew it one time.[5]
Wait after the permit14 calendar days after DOL issues your original or upgraded permit before you can take the skills test.[7][8]
Training before the testYou cannot take the skills test until an approved training provider has finished your training and entered your course completion, and you have met the federal ELDT requirements.[7]
Skills testThree parts, taken in this order: vehicle inspection, basic controls (backing) and a road test. You have to pass all three. The test is given in English and you cannot use an interpreter.[7]
Where skills tests are givenDOL has three CDL skills test sites: Everett, Parkland (Tacoma) and Pasco. You can also test with a state-certified independent third-party examiner, but DOL has to authorize you first. Either way, you start by contacting DOL scheduling.[9][10][7]
Skills test fee$175 for a truck or passenger vehicle test. $100 for a school bus test if you will use the CDL mainly to drive a school bus.[7]
If you failYou wait 3 days before a retest. Passing scores are good for 180 days, counted from the day you passed the first part.[7]
After you passYou wait 24 hours after passing all three parts, then go to a driver licensing office by appointment to have the CDL issued.[7]
02CDL Fees

Washington CDL permit and license fees

These are the fees the Washington DOL publishes for a commercial learner's permit, the tests and a CDL. Each row says who pays it. We list a fee only where the state names it and gives the amount. Checked October 5, 2026.

Washington CDL fees published by the Washington DOL
FeeAmountWho pays it
Learner's permit and knowledge tests
CDL knowledge testOne $35 fee covers the class and endorsement knowledge tests you take within 90 days of the receipt.$35.00[11]Everyone
Commercial learner's permit$40.00[12]A first CDL and a CDL holder moving up a class
Commercial learner's permitThe DOL requires a permit to add an endorsement that needs a skills test (passenger or school bus).$40.00[12]A CDL holder adding an endorsement: with School Bus
Commercial learner's permitThe DOL requires a permit to add an endorsement that needs a skills test (passenger or school bus).$40.00[12]A CDL holder adding an endorsement: with Passenger; without School Bus
Commercial learner's permit, only if you train or test in a tank vehicleThe tank endorsement needs a permit ($40) only if you are testing or training in a tank vehicle. It is not added to the total here.See the note[12]A CDL holder adding an endorsement: with Tank; without Passenger; without School Bus
Skills test
CDL skills test, truck or passengerSame fee with a DOL examiner or an independent third-party examiner. A convenience fee is charged if you pay by card.$175.00[13]A first CDL and a CDL holder moving up a class: without School Bus
CDL skills test, school busFor a school bus test when you will use your CDL primarily to drive a school bus. The fee gets you 2 attempts. A convenience fee is charged if you pay by card.$100.00[13]Everyone: with School Bus; Yes, mainly a school bus
CDL skills test with a school bus endorsementThe DOL lists $100 for a school bus test only if you will use your CDL primarily to drive a school bus, and $175 for a truck or passenger (not school bus) test. It does not list an amount for a school bus test in any other case.See the note[13]Everyone: with School Bus; No
CDL skills test, passengerSame fee with a DOL examiner or an independent third-party examiner. A convenience fee is charged if you pay by card.$175.00[13]A CDL holder adding an endorsement: with Passenger; without School Bus
License
License fee to add a CDL to your Washington license$20.00[11]A first CDL
CDL fee, $17 per year left on your license$17 per year for the time remaining on your current Washington license. With the $20 license fee, the DOL lists a total of $37 to $156.See the note[11]A first CDL
Add a CDL endorsement to your Washington licenseThe DOL lists $20 to add a CDL special endorsement. It does not say whether this is charged once or for each endorsement; it is counted once here.$20.00[11]A CDL holder adding an endorsement
License fee for the higher classThe DOL fee list does not show a fee for moving a CDL up to a higher class. Call 360-902-3900 for the amount.See the note[11]A CDL holder moving up a class

Not in the table for a first CDL, because we could not confirm the amount from the Washington DOL:

  • The CDL fee of $17 for each year left on your current license
  • The federal HazMat background check (TSA), if you add HazMat
  • The skills test fee if you add school bus but will not mainly drive a school bus

Not in the table for a driver who already holds a CDL, because we could not confirm the amount from the Washington DOL:

  • The license fee for the higher class when you move up a class
  • The federal HazMat background check (TSA), if you add HazMat
  • The skills test fee if you add school bus but will not mainly drive a school bus
  • The $40 permit if you train or test in a tank vehicle for the tank endorsement
  • A further $20 for each added endorsement after the first, if the DOL charges the $20 endorsement fee per endorsement (it does not say)

Renewal: Renewing a license with a CDL is $163 for 6 years or $217 for 8 years.[11]

  • The DOL says its fee list gives a general idea of what you would pay and may not cover all situations; call 360-902-3900 for an exact amount.[11]
  • The knowledge test fee covers one attempt at each knowledge test you take within 90 days of the receipt.[14]
  • The fee list also shows "Add CDL special endorsement to a WA driver license" at $20. It does not say whether this is charged when endorsements are issued with a first CDL, so it is not added to the total here.[11]
  • For HazMat, you apply with the TSA for a threat assessment and the DOL says fees apply; the DOL does not state the amount.[15]
  • If you do not pass all 3 parts of the skills test, you schedule a retest and pay any appropriate fees. If you change examiners, a testing fee applies.[13]
  • If you already hold a CDL, you need a commercial learner's permit to move up to a higher class or to add a passenger or school bus endorsement. A tank endorsement needs one only if you test or train in a tank vehicle.[12]
  • The DOL says you do not need a skills test for the tank (unless you train or test in a tank vehicle), HazMat or doubles/triples endorsements; you take the knowledge test.[13]
  • By rule, the $35 examination fee covers a CDL knowledge test, an endorsement knowledge test, or any combination of them.[16]
  • A license with a HazMat endorsement is set to expire when your TSA clearance expires. If the DOL has to move your expiration date earlier, it does not refund the difference.[15]

Fees change. Confirm your total with the Washington DOL before you go. The Washington DOL sets these fees; ELDT.Courses does not collect them.

Want them added up for your class and endorsements? Get the free Washington CDL cheat sheet with your costs.

03Entry-Level Driver Training

ELDT in Washington: what has to be done before you test

Washington adds its own training requirements on top of federal ELDT. State law says no one gets a Washington CDL without completing a course of instruction approved by DOL, or being certified by an employer as having the needed skills and training.[8] The state rule sets minimum training requirements for Class A, B and C licenses, upgrades, and the passenger, school bus and HazMat endorsements, and it requires the training provider to have an application with DOL approving the course and also to be listed on the federal Training Provider Registry.[17]

DOL says only a registered Washington training provider can certify that a driver has met the state training requirements. That can be a registered CDL training school, or your employer if the employer is a registered training provider.[18][19] You have to show proof of both your state and federal training before DOL gives you the skills test.[7] For HazMat, the training course completion has to be on record before you take the HazMat knowledge test.[2]

So if you are getting a Washington CDL, talk to your Washington-registered school or employer before you pay for any course, including online theory. Ask how the course fits into the state-approved training they will certify to DOL. The doubles and triples endorsement has no added training requirement in Washington, only the knowledge test.[7]

Entry-level driver training (ELDT) is a federal rule, so it works the same in Washington as in every other state. If you are getting a Class A or Class B CDL for the first time, upgrading to a Class A or B, or adding a passenger (P), school bus (S) or hazardous materials (H) endorsement for the first time, you have to complete training with a provider listed on FMCSA's Training Provider Registry (TPR).[20]

The state cannot give you the skills test for a Class A or B CDL or a P or S endorsement, or the knowledge test for the H endorsement, until that training is on record.[21] Theory can be done online: the federal definition of theory instruction includes online training.[22] Except for the HazMat endorsement, the theory and behind-the-wheel parts have to be finished within one year of each other.[23]

04Jobs and Pay

Truck driving jobs and pay in Washington

Heavy and tractor-trailer truck drivers (SOC 53-3032) in Washington
Drivers employed (May 2025)40,530[24]
Median pay (May 2025)$64,760 a year, or $31.13 an hour[24]
Average pay (May 2025)$68,230 a year, or $32.80 an hour[24]
Projected jobs, 2024 to 203438,760 in 2024, growing to 40,360 in 2034 (up 4.1%)[25]
Projected openings each year, 2024 to 2034About 4,280 a year, counting new jobs and replacements[25]

The wage figures are from the federal Occupational Employment and Wage Statistics survey. The projections come from Washington's own long-term forecast, published through Projections Central. The two sources give different job totals.

05On the Road

Truck rules on Washington roads

Size and weight limits

Washington legal limits without a permit
Width8 feet 6 inches, including the load[26]
Height14 feet, loaded or empty. The law still puts it on the driver to make sure there is enough clearance on the route.[27]
Single vehicle length40 feet overall, with or without load[28]
Semitrailer length53 feet[28]
DoublesThe two trailers together can be no more than 61 feet[28]
Truck and trailer75 feet overall, with or without load[28]
OverhangWSDOT lists 3 feet of front overhang and 15 feet of rear overhang as legal dimensions[29]
Single axle20,000 pounds[30]
Tandem axle34,000 pounds. Two consecutive sets of tandems can carry 34,000 pounds each when the first and last axles of the two sets are at least 36 feet apart.[30]
Gross weightSet by the state weight table, which is built on a formula written into the statute and depends on the number of axles and the distance between them. The table tops out at 105,500 pounds. A five-axle group reaches 80,000 pounds at 51 feet of spacing.[30]
What controlsWSDOT says legal weight comes from three things: tire size, axle weight and the weight table. Whichever gives the lowest number controls.[31]

Longer combination vehicles

The federal list of grandfathered longer combinations has two Washington entries. The first is a truck tractor with two trailing units, with up to 68 feet of cargo-carrying length and up to 105,500 pounds gross. Doubles with more than 60 feet of cargo-carrying length need an annual overlength permit. The second is a truck-trailer combination with up to 68 feet of cargo-carrying length and an overall length limit of 75 feet. Both are allowed on all National Network routes except SR 410 and SR 123 near Mt. Rainier National Park.[32]

Truck speed limits

Washington law caps the truck speed limit at 60 mph. The basic limits are 25 mph on city and town streets, 50 mph on county roads and 60 mph on state highways.[33] The Secretary of Transportation can raise the limit on a highway to as much as 75 mph, but the limit for vehicles over 10,000 pounds gross weight and for vehicles in combination cannot go above 60 mph. When a Washington speed sign says "trucks," it means vehicles over 10,000 pounds gross weight and all vehicles in combination.[34]

Winter restrictions and chains

Washington has a standing chain law for vehicles over 10,000 pounds gross vehicle weight rating. From November 1 to April 1 you have to carry enough chains to meet the rule on the routes below, whatever the weather or road reports say. The rest of the year you only need them when chains are posted as required.[35][36]

Washington chain rules for vehicles over 10,000 pounds
Extra chainsEvery vehicle over 10,000 pounds must carry at least two extra chains, in case conditions get worse or a chain breaks.[35][36]
Five-axle tractor and tandem semitrailerWhen "chains required" is posted, chains go on at least four drive tires: either all tires on one drive axle, or one tire on each side of both drive axles. On the trailer, the chained tire can be on either of the last two axles.[35]
Six or more axlesWith dual drive axles and "chains required" posted, all tires on one drive axle are chained, plus one tire on each side of the other drive axle, plus one tire on the last axle of the trailer.[35]
Type of chainTwo side chains with hardened metal cross chains. Plastic chains are not allowed. WSDOT says cable chains are allowed.[35][36]
Automatic chainsIf you run automatic tire chains, you still have to carry regular chains for the outside drive tires.[35]
Chain-carry routesI-90 from North Bend (milepost 32) to Ellensburg (milepost 101). I-82 from Ellensburg Exit 3 to Selah Exit 26. US 2 from Dryden to Index. US 12 from Packwood to Naches. US 97 from milepost 145 to the US 2 junction, and from the Columbia River to Toppenish. SR 410 from Enumclaw to Naches. SR 20 from Tonasket to Kettle Falls and from Newhalem to Winthrop. SR 155 from Omak to Nespelem. SR 970 from milepost 0 to 10. SR 14 from Gibbons Creek (milepost 18) to Cliffs Road (milepost 108.40). SR 542, the Mt. Baker Highway, from milepost 22.91 to 57.26.[35]
Local deliveriesTrucks making local deliveries shown on the bills of lading, and not crossing the mountain pass, do not have to carry chains while they stay outside a chain-required area.[35]

The rule and WSDOT's page call the US routes "SR-2," "SR-12" and "SR-97." WSDOT or the State Patrol can keep any vehicle out of a chain control area if they decide it will have trouble getting through safely. See WSDOT's chain requirements page for the placement diagram.

Seasonal and posted roads

When WSDOT decides an emergency road condition exists, such as a freeze and thaw cycle, it restricts or closes that stretch of highway right away. Signs go up at each end of the restricted segment and at every state highway that crosses it. The signs read "emergency load restrictions" or "severe emergency load restrictions," and the limit is a maximum load per tire based on tire size. WSDOT can issue permits for school buses and for trucks hauling perishables or goods needed for the health and welfare of local residents.[37] WSDOT's route and commercial vehicle restrictions page links to current restrictions for oversize and overweight vehicles, and you can sign up there for freight alerts by email or text.[38]

HazMat routes and tunnels

The federal registry lists four restricted locations in Washington, all in King County: three in Seattle and one in SeaTac.[39]

  • I-90, Seattle, mileposts 3 to 6: flammable loads cannot go through the Mercer Island tunnel or the tunnel on the west side of Lake Washington when the sprinkler systems are not working or are being tested.
  • I-5, Seattle, milepost 164: flammable loads cannot go through the tunnel under the convention center when the sprinkler systems are not working or are being tested.
  • SR 99 tunnel, Seattle, mileposts 30.30 to 32.79: hazardous materials are prohibited in the tunnel, a distance of 2.49 miles.
  • 188th S, SeaTac: hazardous materials are prohibited in both directions between 28th Avenue South and 16th Avenue South.

Check the FMCSA hazardous materials route registry by state before you route a load.

Tolls and transponders

Good To Go is WSDOT's toll account, and WSDOT says it works on every toll road in Washington.[40] WSDOT lists these toll facilities: the SR 520 Bridge, the SR 99 tunnel, the Tacoma Narrows Bridge, the I-405 and SR 167 express toll lanes, and the SR 509 Expressway.[41] A Good To Go account has no monthly fee. If you use a toll road without an account, WSDOT photographs the plate and mails a bill to the registered owner, and the Pay By Mail rate is $2 higher.[40]

The Tacoma Narrows Bridge has toll booths. Tolls are collected only on trips headed toward Tacoma, and the booths take cash, credit cards or a mobile wallet for $1 more than the pass rate. Tolls there go up with the number of axles.[42] In the SR 99 tunnel, vehicles with more than two axles also pay a higher rate based on the axle count.[43] Open an account or pay a bill at MyGoodToGo.com, the Good To Go toll account site.

Fuel tax (IFTA)

Washington diesel fuel tax
IFTA diesel rate, 4th quarter 2026$0.595 per gallon. Washington raised its special fuel (diesel) rate from $0.584 to $0.595 on July 1, 2026.[44][45]
Who handles itThe Department of Licensing runs fuel tax and IFTA for carriers based in Washington, through its prorate and fuel tax offices and the License Express online system.[46]
Decals$10 per set of two decals for each qualified vehicle, one on each side. The IFTA license itself has no fee. Decals are valid January 1 to December 31.[46]

IFTA rates can change every quarter. The 4th quarter 2026 matrix was marked not final until December 4, 2026 when this page was checked.

Oversize and overweight permits

WSDOT Commercial Vehicle Services issues oversize and overweight permits, and only for loads that cannot be divided. Most routine permits can be self-issued online at any hour through WSDOT's permit program, eSNOOPI Pro.[47] You can also use a permit agent or visit a WSDOT permit office. Permits are not sold at the Ports of Entry, and you are responsible for checking your own route for restrictions and overhead clearance. Start at WSDOT's commercial vehicle permits page.[29]

Truck parking

Many WSDOT rest areas have truck parking, and WSDOT says trucks may stay up to 11 hours.[48] The general rest area limit in state law is 8 hours in any 24-hour period, with commercial vehicles allowed to park up to an hour past their federally required rest period.[49]

On I-5, WSDOT's Truck Parking Management System (TPIMS) shows how many truck spaces are open at certain rest areas and weigh stations and predicts availability up to four hours ahead. WSDOT says drivers with a USDOT number can see it through the Drivewyze and ParkerTruck mobile apps.[48] See WSDOT's truck parking at rest areas page for the list of sites.

Weigh station bypass

WSDOT runs its own weigh station e-screening program. The equipment is at 11 weigh stations and four virtual weigh-in-motion sites. About half a mile before the station, scales in the road weigh the truck while a reader identifies it by transponder or license plate, and the system checks registration, weight, height and the carrier's safety rating. A green light on the transponder means you can bypass. A red light means pull in. If the transponder shows no light, follow the roadside signs.[50][51]

Carriers with vehicles of 16,000 pounds gross vehicle weight or more can buy a transponder from WSDOT for a one-time $35 fee, and there are no other fees to use it in Washington.[52] The Washington State Patrol's Commercial Vehicle Division lists five Ports of Entry: Bow Hill (I-5 southbound), Cle Elum (I-90 westbound, milepost 80), Plymouth (I-82 northbound), Ridgefield (I-5) and Spokane (I-90 westbound, milepost 299, Liberty Lake).[53]

06Paying for Training

Help paying for CDL training in Washington

Washington's Eligible Training Provider List (ETPL) is the official list of training programs that can take students using a Workforce Innovation and Opportunity Act (WIOA) Individual Training Account, or drawing extra weeks of unemployment benefits through the state's Training Benefits Program. Programs on the list have to be located in Washington and meet performance standards for employment, earnings and completion.[54]

You can look through it with the Career Bridge search for ETPL-approved programs.[54]

To ask about funding, contact your local WorkSource career center. Washington's 12 workforce development councils run the WorkSource system.[54] Ask three things: whether you qualify for WIOA training funds, which CDL programs on the list they will pay for, and what paperwork they need before you enroll. Get the answer before you pay a school.

07Veterans

Veterans and military drivers in Washington

Washington military experience waiver

Federal rules let a state waive the CDL skills test for drivers with military commercial vehicle experience.[55] Washington state law lets DOL waive the skills test and the state training course requirement for applicants who meet the federal rule, and for current or former service members it can waive the knowledge test too.[8]

DOL says you qualify for the military experience waiver if you are a Washington resident, have two or more years of experience driving commercial vehicles as part of your military job, are on active duty or within 12 months of an honorable discharge, and meet the requirements on the federal Application for Military Skills Test Waiver. Your commanding officer completes and signs the application. You email it to DOL with a copy of your DD214, NGB22 or equivalent document, wait for DOL's approval email, then make an appointment at a driver licensing office. You still need a DOT physical. DOL's CDL military experience waiver page has the applications and the document list.[56]

GI Bill and VR&E

If you plan to use VA education benefits, check the school first. The VA's GI Bill Comparison Tool lets you look up schools and training programs.[57] Veterans with a service-connected disability can also ask about Veteran Readiness and Employment (Chapter 31).[58] Ask any school whether it is approved for VA benefits before you enroll.

08Behind the Wheel

Behind-the-wheel training in Washington

For a CDL, passenger or school bus endorsement, theory is only half of ELDT. The range and road training has to be done in a truck or bus with a behind-the-wheel provider that is also listed on the Training Provider Registry.[20] The HazMat endorsement is theory only.[59]

To find one near you, use the FMCSA Training Provider Registry provider search: pick the license or endorsement, choose Behind-the-Wheel, and enter your location.[59] You can take theory from one provider and behind-the-wheel from another.

09Your Federal Record

Check your Training Provider Registry record

When you finish a course, your training provider has until midnight of the second business day to send your completion to the Training Provider Registry.[60]

You can look it up yourself with FMCSA's Check Your Record tool on the Training Provider Registry. Enter your license or permit number and state, your date of birth, and your first and last name exactly as they appear on your license or permit.[61]

10Common Questions

Washington CDL questions

How long do I have to wait after getting my Washington CDL permit to take the skills test?

Fourteen calendar days from the day DOL issues your original or upgraded commercial learner's permit. You also cannot test until your training provider has entered your course completion and your federal ELDT is on record.[7][8]

Does Washington have its own CDL training requirements besides federal ELDT?

Yes. State law requires a course of instruction approved by the Department of Licensing, or certification by an employer, before a CDL is issued. DOL says only a registered Washington training provider can certify that you met the state requirements, and you have to show proof of both state and federal training before the skills test.[8][17][18][7]

What is the truck speed limit in Washington?

No more than 60 mph. State law caps the limit at 60 mph for vehicles over 10,000 pounds gross weight and for vehicles in combination, even on highways where the limit for other vehicles has been raised as high as 75 mph. It can be posted lower.[34]

When do trucks have to carry chains in Washington?

From November 1 to April 1, vehicles over 10,000 pounds have to carry chains on the routes listed in the state rule, including I-90 between North Bend and Ellensburg, regardless of conditions. Every vehicle over 10,000 pounds also has to carry at least two extra chains. Outside those dates, chains are needed when they are posted as required.[35][36]

Where can I take the CDL skills test in Washington?

The Department of Licensing has three CDL skills test sites, in Everett, Parkland (Tacoma) and Pasco. You can also test with a state-certified independent third-party examiner once DOL has authorized you. The fee is $175 for a truck or passenger vehicle test.[9][10][7]

11Nearby States

Trucking guides for states next to Washington

See every state on the Trucking by State page.

How to find approved training in Washington

ELDT.Courses does not offer CDL or ELDT training in Washington. Train with a registered Washington training provider. The Department of Licensing says that can be a registered CDL training school, or your employer if the employer is a registered training provider, and only a registered Washington provider can certify your training.[18]

Washington DOL training requirements →
12Sources

Where these facts come from

Every fact on this page comes from an official source that was opened and read on the date shown. Rules, rates and wages change, so check the source before you rely on a number.

  1. Washington State Department of Licensing. Commercial driver licenses (CDL). Checked October 4, 2026.
  2. Washington State Department of Licensing. Getting a commercial driver license (CDL). Checked October 4, 2026.
  3. Washington State Department of Licensing. Commercial Driver License (CDL) Guide (PDF). Checked October 4, 2026.
  4. Washington State Department of Licensing. Commercial driver guides. Checked October 4, 2026.
  5. Washington State Department of Licensing. Commercial learner's permit (CLP). Checked October 4, 2026.
  6. eCFR. 49 CFR 391.11, General qualifications of drivers. Checked October 4, 2026.
  7. Washington State Department of Licensing. CDL skills test. Checked October 4, 2026.
  8. Washington State Legislature. RCW 46.25.060, Knowledge and skills examination, exemptions, fee distribution. Checked October 4, 2026.
  9. Washington State Department of Licensing. CDL skills test locations. Checked October 4, 2026.
  10. Washington State Department of Licensing. Find an independent third-party examiner. Checked October 4, 2026.
  11. Washington State Department of Licensing. Driver licensing fees. Checked October 5, 2026.
  12. Washington State Department of Licensing. Commercial learner's permit (CLP). Checked October 5, 2026.
  13. Washington State Department of Licensing. CDL skills test. Checked October 5, 2026.
  14. Washington State Department of Licensing. CDL knowledge test. Checked October 5, 2026.
  15. Washington State Department of Licensing. Hazardous materials endorsement (hazmat). Checked October 5, 2026.
  16. Washington State Legislature. WAC 308-100-050, Examination fees. Checked October 5, 2026.
  17. Washington State Legislature. WAC 308-100-033, Minimum training requirements. Checked October 4, 2026.
  18. Washington State Department of Licensing. CDL training requirements. Checked October 4, 2026.
  19. Washington State Legislature. WAC 308-100-035, Employer certification. Checked October 4, 2026.
  20. eCFR. 49 CFR 380.609, General entry-level driver training requirements. Checked October 4, 2026.
  21. eCFR. 49 CFR 383.73, State procedures. Checked October 4, 2026.
  22. eCFR. 49 CFR 380.605, Definitions (theory instruction). Checked October 4, 2026.
  23. eCFR. 49 CFR 380.603, Applicability (entry-level driver training). Checked October 4, 2026.
  24. U.S. Bureau of Labor Statistics. Occupational Employment and Wage Statistics, Washington, May 2025. Checked October 4, 2026.
  25. Projections Central (Projections Managing Partnership). Long-Term Occupational Projections (2024-2034). Checked October 4, 2026.
  26. Washington State Legislature. RCW 46.44.010, Outside width limit. Checked October 4, 2026.
  27. Washington State Legislature. RCW 46.44.020, Maximum height, impaired clearance signs. Checked October 4, 2026.
  28. Washington State Legislature. RCW 46.44.030, Maximum lengths. Checked October 4, 2026.
  29. Washington State Department of Transportation. Commercial vehicle permits. Checked October 4, 2026.
  30. Washington State Legislature. RCW 46.44.041, Maximum gross weights, wheelbase and axle factors. Checked October 4, 2026.
  31. Washington State Department of Transportation. Legal vehicle weight. Checked October 4, 2026.
  32. eCFR. 23 CFR Part 658, Truck size and weight, route designations (including Appendix C). Checked October 4, 2026.
  33. Washington State Legislature. RCW 46.61.400, Basic rule and maximum limits. Checked October 4, 2026.
  34. Washington State Legislature. RCW 46.61.410, Increases by secretary of transportation, maximum speed limit for trucks. Checked October 4, 2026.
  35. Washington State Legislature. WAC 204-24-050, Use of tire chains or other traction devices. Checked October 4, 2026.
  36. Washington State Department of Transportation. Chain requirements for vehicles over 10,000 pounds. Checked October 4, 2026.
  37. Washington State Legislature. WAC 468-38-080, Emergency load restrictions for heavy vehicles. Checked October 4, 2026.
  38. Washington State Department of Transportation. Route and commercial vehicle restrictions. Checked October 4, 2026.
  39. FMCSA. National Hazardous Materials Route Registry: Washington (May 2026). Checked October 4, 2026.
  40. Washington State Department of Transportation. Good To Go! accounts and passes. Checked October 4, 2026.
  41. Washington State Department of Transportation. Toll roads, bridges and tunnels. Checked October 4, 2026.
  42. Washington State Department of Transportation. Tacoma Narrows Bridge tolling. Checked October 4, 2026.
  43. Washington State Department of Transportation. SR 99 Tunnel tolling. Checked October 4, 2026.
  44. IFTA, Inc.. IFTA Tax Matrix, 4th Quarter 2026 Fuel Tax Rates. Checked October 4, 2026.
  45. Washington State Department of Licensing. Prorate and fuel tax news and updates: Fuel tax rate changes in 2026. Checked October 4, 2026.
  46. Washington State Department of Licensing. Get your license and decals: IFTA. Checked October 4, 2026.
  47. Washington State Department of Transportation. Commercial vehicles. Checked October 4, 2026.
  48. Washington State Department of Transportation. Truck parking at rest areas. Checked October 4, 2026.
  49. Washington State Legislature. RCW 47.38.020, Limitations on use of rest areas. Checked October 4, 2026.
  50. Washington State Department of Transportation. Weigh station e-screening technology. Checked October 4, 2026.
  51. Washington State Department of Transportation. Transponder program and benefits. Checked October 4, 2026.
  52. Washington State Department of Transportation. Buy a transponder. Checked October 4, 2026.
  53. Washington State Patrol. Commercial Vehicle Contacts. Checked October 4, 2026.
  54. Career Bridge, Washington Workforce Training and Education Coordinating Board. What is the Eligible Training Provider List?. Checked October 4, 2026.
  55. eCFR. 49 CFR 383.77, Substitute for knowledge and driving skills tests for drivers with military CMV experience. Checked October 4, 2026.
  56. Washington State Department of Licensing. Commercial Driver License (CDL) military experience waiver. Checked October 4, 2026.
  57. U.S. Department of Veterans Affairs. GI Bill Comparison Tool. Checked October 4, 2026.
  58. U.S. Department of Veterans Affairs. Veteran Readiness and Employment (Chapter 31). Checked October 4, 2026.
  59. FMCSA. Training Provider Registry: Find a Provider. Checked October 4, 2026.
  60. eCFR. 49 CFR 380.717, Training certification. Checked October 4, 2026.
  61. FMCSA. Training Provider Registry: Check Your Record. Checked October 4, 2026.

Last verified: . This page is general information, not legal advice. See something out of date? Tell us through the contact page.